How to connect icemaker. plumbing 2019-02-06

How to connect icemaker Rating: 8,6/10 546 reviews

How to Connect an Ice Maker

how to connect icemaker

How to install a refrigerator water line? Step 4 — Use the water valve saddle valve that came with your fridge water line kit and attach it to the cold water pipe using a screwdriver and the clamps it came with. Also, I have heard that hot water freezes faster than cold water. Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook. Water supply line tubing for fridge Leave extra 8 to 10 feet to allow to pull fridge out when needed Step 7 — Put the compression nut and ferrule onto the water tubing that came with your kit. Even some installation kits can lead you in the wrong direction heading for leaks in your future. Leave 4' of tube extra, coiled behind the fridge. Thanking ahead for your advise.

Next

Connect an RO System to a Refrigerator or Ice maker

how to connect icemaker

If your refrigerator does not have a compression fitting, install the fitting that comes with the ice maker kit. Get the screws on the clamps tight enough until the sealing washer or gasket swells up. Usually behind where a refrigerator is installed, there will be a water valve that you can use to hook cold water to your fridge. To insure trouble free performance for the life of the refrigerator, there are a few important things you should do when installing an automatic ice maker. There are no washers to replace. Invest a bit more money in your ice maker to make sure it has a drain pump installed, which will ensure that it functions better, requires less installation work, and is less likely to leak.

Next

How to Install a Water Line for a Refrigerator Ice Maker

how to connect icemaker

Smaller models generally yield less ice and are less expensive. Be sure to use a plastic ring for plastic tubing; brass rings are made for copper pipe and can cut through plastic tubing. Richard replaced the plastic tubing with copper tubing, and instead of using a saddle valve, he connected it to the cold water line using a compression connection with a multi-turn valve, which he soldered into the cold water pipe using a T fitting. Wipe the area of your cold water pipe that you will attach the valve onto with a clean, wet cloth. The beauty of plastic tubing is that it is flexible. They have a stainless steel ball inside the valve body that has a one half inch hole drilled through its center.

Next

Ice Maker Connector

how to connect icemaker

Open the cold water faucet to let water drain out of the pipe. Now, turn the new water valve on with the end of the water line in the bucket. A drain pump is a pump that pulls waste water away from different sources, including ice makers, and brings it to a kitchen drain. In my opinion the braided stainless steel icemaker supply lines are the best option. It is also necessary to install an inline valve to permit turning off the ice maker connection as shown.

Next

Fittings Needed to Connect an Ice Maker to Plastic Tubing

how to connect icemaker

While you do not want 20 feet of pipe behind your refrigerator, leave enough slack so that you can pull the fridge away from the wall enough to access the rear of the fridge without putting tension on the water line. Icemaker Supply Kit with Plastic Tube and Saddle Valve Braided Stainless Steel Icemaker Supply Line The tubing you use to run from the supply valve to the refrigerator is another critical choice. If you have a newer model, it may be located in the refrigerator door. The salesperson at the appliance store sold me a kit that clamps onto a regular water pipe. Use a compression fitting to attach the piping to the ice maker. It is a common question that we have to deal with on every day bases.


Next

3 Ways to Install an Ice Maker

how to connect icemaker

Shut off the water and drain the pipe. Avoid using the bottom of the pipe, as this may draw sediment into the ice maker. If you can't use a flare fitting you must carefully install the one quarter inch tubing and inspect the refrigerator every 10 minutes or so after it has been rolled back into position. At the actual ice maker connection it will be necessary to use the small diameter plastic tubing to the ice maker fitting. Take the polypropylene hose and connect it to valve. Step 8 — Now your plastic water tube should be connected to the cold water valve you just installed. Leave extra slack high on the fridge so that it can still be easily moved in and out.

Next

How to connect ice maker

how to connect icemaker

Put the ice maker into its place under the counter. However, there are a number of things that can go wrong and cause flooding damage to your home if not done right. The connection to the existing supply line is made with a saddle valve. The other side of the fitting is a compression fitting, which you will use to connect the plastic tubing to the refrigerator. The first thing I would do is take the clamp-on valve kit back to the store. I filled three identical glasses with three ounces of water. For me I had to go to 2 home depots and one Lowes Store.

Next

plumbing

how to connect icemaker

There should be one in the kit. Run the water line into the bucket until the water is perfectly clean and clear. If not, you will need to run a line to the nearest cold water pipe, which is probably in the floor below your kitchen. Here is a step-by-step water line installation refrigerator guide. . Refrigerators with automatic ice makers are a great convenience, especially on a hot day. As you move the ice maker, be sure to slowly pull the piping out through the holes in the sides of your cupboard to keep it from getting stuck under the machine.

Next

plumbing

how to connect icemaker

Or what are all my options. If you have a model of refrigerator that is 10 years old or older, the ice maker, including the part that hooks up to the copper tubing, is likely to be located in the freezer. When you rotate the valve handle 90 degrees to the full open position, the water flows through the valve unobstructed. The slow tightrope walks from the sink to the freezer while balancing flimsy ice cube trays will be a dim memory in just a few days my friend. It is not uncommon for those tiny valves to deliver inadequate water supply to the ice maker.

Next